Roofing — New Installation + Repairs

New roofs, leak repairs, flashing fixes, and storm damage corrections — done with proper details and clean finishes.

Roof problems usually come from a few causes: failed flashing, cracked pipe boots, broken/missing materials, poor transitions, or underlayment issues. We diagnose the path of water, fix the detail (not just the symptom), and verify everything is sealed.

Request Service View Install & Repair

Serving Merced and surrounding areas • Licensed & insured • Install + repairs + maintenance

Fast triage: leak vs flashing vs missing shingles vs soft spots (optional)
✓ New roof installs • ✓ Leak repair • ✓ Flashing/valley/vent fixes • ✓ Storm damage repairs

Roofing Services with wiBuilder

We provide both new installations and repairs for common roofing systems. Our approach: find the water path, fix the detail (flashing/boot/transition), then restore the roof cleanly.

New Installation

Complete installs for remodels, additions, replacements, and full roof refresh projects.

Install scope
Shingles Architectural/asphalt shingle systems (as scoped).
Tile Roofing Concrete/clay tile installs and reset (as scoped).
Underlayment Waterproof layers designed for your system + slope.
Flashing & Valleys Critical transitions to stop leaks long-term.
Ventilation Ridge/roof vents to help roof life + comfort.
Gutters/Edges Drip edge + clean terminations (as needed).
Sealing Details Pipe boots, penetrations, skylight transitions.
Final Walkthrough Cleanup + final inspection points reviewed.

What a “complete install” typically includes

  • Remove/prepare surface as needed (tear-off or overlay per scope)
  • Replace damaged decking sections where discovered (as approved)
  • Underlayment + ice/water protection where applicable
  • Valley + flashing install (chimney, walls, skylights, transitions)
  • Install roofing material (shingle/tile/etc.)
  • Ventilation details + edge/drip details
  • Cleanup + magnet sweep + final check

Typical install upgrades (optional)

  • Higher-grade underlayment and improved flashing packages
  • Ventilation improvements (ridge vent, intake balancing)
  • Gutter/edge improvements where water control is needed

Note: Final system details depend on roof slope, existing layers, penetrations, and local requirements.

Repairs + Restoration

Leak repairs, storm damage, and detail corrections — done at the source.

Repair scope
Leak Diagnostics Find the entry point before sealing.
Storm Damage Missing shingles/tiles, wind lift, debris impacts.
Flashing / Valley Repair Wall transitions, chimneys, skylights, valleys.
Vent / Boot Repairs Pipe boots, roof vents, penetration sealing.
Shingle/Tile Replace Selective replacement + blending where possible.
Soft Spots Decking/rot evaluation and localized repairs.
Roof Coating Coatings where appropriate (system-dependent).
Fascia Repairs Edge wood repairs tied to water control.

Typical repair process

  1. Inspect and trace the likely water path (not just the stain)
  2. Remove/loosen enough material to access the failure point
  3. Repair detail: flashing, boot, transition, valley, sealing
  4. Replace roofing material and re-seal penetrations
  5. Final check + cleanup

Repair notes

  • Leaks often show up far from the entry point—diagnosis matters.
  • Temporary “tar patches” usually fail; detail repairs last longer.
  • If decking is compromised, repair may expand after inspection.

Quick Roofing Triage (Optional)

Pick what you’re seeing — we’ll suggest the likely next step.

Likely next step

Note: We confirm on-site. Active leaks usually get priority scheduling.

Estimate Install or Repair Cost

Quick planning tool. Final pricing depends on roof pitch, access, material type, layers/tear-off needs, and condition of decking/flashing.

  • Install: uses area-based baseline (sq ft).
  • Repair: uses typical service ranges.

Estimate only. Final price confirmed after inspection.

Estimated Project Range

Use the estimator to see a typical range. Your estimate will appear here after you submit.

Mode:
Type:
Size/Extent:
Pitch/access:

Estimated Range:

If decking/underlayment issues are discovered, scope may expand after inspection.

Common Roofing Questions

Fast answers — we’ll confirm details during inspection.

Not always. Many leaks come from flashing, valleys, vents, or transitions. We trace the water path and repair the detail first.

Typically: tear-off/prepare as scoped, underlayment, flashing/valleys, install roofing materials, ventilation details, cleanup, and final check.

Water can travel along framing and underlayment before showing up inside. That’s why diagnosing the entry point matters.

Yes for many cases. If there’s widespread failure, multiple leaks, or underlayment/decking problems, a broader fix may be recommended.

Request Roofing Service

Tell us if you need a new installation or a repair and we’ll confirm scope and next steps.

Your information is used only to follow up on your roofing request.